The Best Custom Boat Lines, Custom Colored Ropes, & Special Assemblies made to Your Specifications We offer a wide selection of Stainless Steel & Galvanized Marine Hardware
We offer marine grade hardware in both stainless steel and galvanized including anchors, anchor shackles, bow shackles, swivel eye hooks, eye hooks, spring clips, thimbles, master links, trigger release shackles, quick release snap shackles, bolted safety shackles, anchor swivels, and anchor chain. Only a small portion of what is available is shown. Ask us for a special assembly of custom colored rope & marine hardware for anchor lines, mooring lines, dock lines, shore lines, tow bridles, & tow lines. Denver Rope is a factory direct-wholesale distributor for Miami Cordage located in Miami, FL. A family run business serving the marine industry since 1965.
Anchor Selection Guide
Above is a bin of galvanized Super Hooker Fluke Anchors
For High performance, but in a light weight alloy, we offer Fortress FX Series Anchors
We offer a wide selection of anchors on-hand and we are a distributor of Fortress Anchors
General Note Concerning Anchor Chain Diameter Sizing and Anchor tDiameter Sizing
Most chain has a WLL greater than an equally sized Anchor Shackle / Anchor Swivel. Therefore, generally increase a load rated shackle diameter 1/16” above the chain diameter. Therefore for 3/8” anchor chain, specify a 7/16” load rated shackle.
For the case of stainless steel bow shackles where the shackle pin is NOT load rated, the shackle size can generally be increased by an 1/8” above the chain diameter. Therefore for 3/8” anchor chain, specify a 1/2” stainless steel bow shackle.
In either case, please verify using both the chain and shackle specifications, that the shackle pin will pass through the inside width / inside window of the chain. Be aware that the shackle ears will NOT pass through the inside chain window, only the shackle pin will fit through the chain window. Secondly, the shackle pin needs to be secured using stainless steel seizing wire, nylon wire ties, and or lock-tight specified for water usage. Alternately, specify a bolted shackle. After each use, inspect all equipment. In the case of connecting a shackle to anchor: 1. The shackle ears will need to pass through the anchor shank’s shackle slot, AND 2. The shackle pin will need to pass through the inside chain window. Verify using the hardware specifications that the equipment is properly matched to work together as a system.
Most chain has a WLL greater than an equally sized Anchor Shackle / Anchor Swivel. Therefore, generally increase a load rated shackle diameter 1/16” above the chain diameter. Therefore for 3/8” anchor chain, specify a 7/16” load rated shackle.
For the case of stainless steel bow shackles where the shackle pin is NOT load rated, the shackle size can generally be increased by an 1/8” above the chain diameter. Therefore for 3/8” anchor chain, specify a 1/2” stainless steel bow shackle.
In either case, please verify using both the chain and shackle specifications, that the shackle pin will pass through the inside width / inside window of the chain. Be aware that the shackle ears will NOT pass through the inside chain window, only the shackle pin will fit through the chain window. Secondly, the shackle pin needs to be secured using stainless steel seizing wire, nylon wire ties, and or lock-tight specified for water usage. Alternately, specify a bolted shackle. After each use, inspect all equipment. In the case of connecting a shackle to anchor: 1. The shackle ears will need to pass through the anchor shank’s shackle slot, AND 2. The shackle pin will need to pass through the inside chain window. Verify using the hardware specifications that the equipment is properly matched to work together as a system.
The shackle ears will not fit through the anchor chain inside width / window, but the shackle pin will. Generally, select the largest shackle pin that will fit through the inside chain window, where the rule-of-thumb is to specify the shackle diameter to be a 1/16” larger than the chain diameter." width="470" height="351" /> The shackle ears will not fit through the anchor chain inside width / window, but the shackle pin will. Generally, select the largest shackle pin that will fit through the inside chain window, where the rule-of-thumb is to specify the shackle diameter to be a 1/16” larger than the chain diameter.
The shackle ears will not fit through the anchor shank’s shackle slot. Rotate the shackle so the ears will pass through the slot and or enlarge the slot with a conical honing bit or iron rasp file. Spray the enlarged slot with cold galvanized paint. The shackle pin is connected to the anchor chain." width="470" height="351" /> The shackle ears will not fit through the anchor shank’s shackle slot. Rotate the shackle so the ears will pass through the slot and or enlarge the slot with a conical honing bit or iron rasp file. Spray the enlarged slot with cold galvanized paint. The shackle pin is connected to the anchor chain.
Anchor Line Scope Ratio Diagram
Anchor Line Assembly Diagram
Anchor Rode Assembly Diagram
Fortress Aluminum FX Series Anchors
Fortress FX Series Anchor
Sets fast & penetrates deeper for incredible holding power
Product Description
The Fortress Anchor is precision-machined from an aluminum alloy that is as strong as steel, but only half the weight making it extremely easy to handle. The Fortress Anchor is sharper than heavy, dull edged steel anchors and will set faster and penetrate deeper for incredible holding power. The adjustable 32° to 45° fluke angle is an exclusive, patented feature that dramatically increases holding power in problem soft and mud bottoms.
| Fortress Aluminum FX Series Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Boat Length (ft) | Anchor Weight (lb) | Holding Power (lb) | Shank Length (in) | Fluke Length (in) | Stock Length (in) | Chain Diam (in) | Rope Diam (in) | Shackle Size (in) |
| ANFX7 | 16-27 | 4 | 700 | 24 | 14 | 19 | 3/16 | 3/8 | 1/4 |
| ANFX11 | 28-32 | 7 | 900 | 27 | 16 | 22 | 1/4 | 3/8 | 1/4 |
| ANFX16 | 33-38 | 10 | 1,250 | 31 | 18 | 25 | 5/16 | 1/2 | 5/16 |
| ANFX23 | 39-45 | 15 | 2,000 | 36 | 21 | 29 | 3/8 | 5/8 | 3/8 |
| ANFX37 | 46-51 | 21 | 3,000 | 40 | 24 | 32 | 3/8 | 3/4 | 7/16 |
| ANFX55 | 52-58 | 32 | 4,000 | 46 | 27 | 37 | 1/2 | 7/8 | 1/2 |
| ANFX85 | 59-68 | 47 | 5,250 | 51 | 30 | 41 | 1/2 | 1 | 5/8 |
| ANFX125 | 69-150 | 69 | 6,750 | 56 | 33 | 45 | 1/2 | 1-1/4 | 5/8 |
Fortress Aluminum Guardian Series Anchors
Fortress Guardian Anchor
Precision-machined from an alloy that is as strong as steel & half the weight
Product Description
The Guardian Anchor is a value priced anchor from Fortress that’s precision-machined from an alloy that is as strong as steel, but only half the weight. The Guardian Anchor has less machining stems than the Fortress, with 32° angle only and non-anodized finish. Easy to disassemble making it an excellent spare or storm anchor that is easy to store. Rustproof and easy to manage weight. Second only to Fortress in holding power. An affordable alternative to heavy steel anchors. One Year Parts Replacement Warranty.
| Fortress Aluminum Guardian Series Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Boat Length (ft) | Anchor Weight (lb) | Holding Power (lb) | Shank Length (in) | Fluke Length (in) | Stock Length (in) | Chain Diam (in) | Rope Diam (in) | Shackle Size (in) |
| ANFG5 | 12-16 | 2.50 | 350 | 19 | 11 | 16 | 3/16 | 3/8 | 3/16 |
| ANFG7 | 17-22 | 4.00 | 575 | 22 | 13 | 18 | 3/16 | 3/8 | 3/16 |
| ANFG11 | 23-27 | 6.00 | 750 | 25 | 15 | 20 | 3/16 | 3/8 | 1/4 |
| ANFG16 | 28-33 | 7.00 | 1,075 | 29 | 17 | 23 | 1/4 | 3/8 | 1/4 |
| ANFG23 | 34-41 | 13.00 | 1,625 | 33 | 19 | 27 | 5/16 | 1/2 | 5/16 |
| ANFG37 | 42-47 | 18.00 | 2,500 | 38 | 22 | 31 | 3/8 | 5/8 | 3/8 |
| ANFG55 | 48-53 | 29.00 | 3,500 | 43 | 25 | 35 | 3/8 | 3/4 | 7/16 |
| ANFG85 | 54-62 | 42.00 | 4,625 | 48 | 28 | 39 | 1/2 | 7/8 | 1/2 |
| ANFG125 | 63-73 | 65.00 | 6,000 | 53 | 31 | 43 | 1/2 | 1 | 5/8 |
Danforth Hi-Tensile Galvanized Anchors
Danforth Hi-Tensile Galvanized Anchor
Toughest & most durable anchor that features high holding power
Product Description
The Danforth Hi-Tensile Anchor is the toughest, most durable anchor and features very high holding power. The flukes are fabricated for additional strength and then beveled to allow quick deep bottom penetration. Hot dip galvanized finish. Each shank is made from drop forged steel.
| Danforth Hi-Tensile Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Boat Length (ft) | Anchor Weight (lb) | Holding Power (lb) | Anchor Height (in) | Anchor Width (in) | Fluke Height (in) | Chain Diam (in) | Rope Diam (in) | |
| AND5HT | to 31 | 5 | 1,000 | 21.50 | 16.50 | 11.75 | 5/16 | 1/2 | |
| AN12HT | 32-42 | 5 | 1,800 | 28.25 | 21.50 | 13.50 | 1/4 | 1/2 | |
| AND20HT | 43-50 | 20 | 2,500 | 35.00 | 26.75 | 19.00 | 7/16 | 5/8 | |
| AND35HT | 51-64 | 35 | 3,800 | 40.75 | 31.00 | 22.00 | 3/4 | – | |
| AND60HT | 65-73 | 60 | 5,500 | 50.00 | 38.00 | 27.00 | 5/8 | – | |
| AND90HT | 74-75 | 90 | 6,300 | 54.00 | 41.00 | 29.24 | 3/4 | – | |
| AND150HT | 76-80 | 150 | 7,000 | 57.25 | 43.50 | 30.50 | 3/4 | – | |
| AND190HT | 81-83 | 190 | 7,700 | 61.00 | 46.00 | 33.50 | 7/8 | – | |
Danforth Standard Galvanized Anchors
Danforth Standard Galvanized Anchor
High holding power and great durability
Product Description
Danforth anchors offer high holding power & great durability at a moderate cost. The flukes are strong & wide permitting the anchor to hold your boat in place in tough conditions with angled crown plates that give this anchor quick, deep penetration. Hot dip galvanized finish for long lasting corrosion resistance.
| Danforth Standard Galvanized Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Boat Length (ft) | Anchor Weight (lb) | Holding Power (lb) | Anchor Height (in) | Anchor Width (in) | Fluke Height (in) | Chain Diam (in) | Rope Diam (in) | Line Length (ft) |
| AND35 | to 10 | 3-1/2 | 160 | 17.25 | 13.00 | 9.00 | 3/16 | 7/16 | 70 |
| AND5 | 11-17 | 5 | 300 | 19.50 | 14.75 | 10.50 | 3/16 | 7/16 | 80 |
| AND9 | 18-27 | 9 | 600 | 24.00 | 18.25 | 12.00 | 3/16 | 7/16 | 90 |
| AND14 | 28-31 | 14 | 920 | 28.25 | 21.50 | 14.25 | 1/4 | 7/16 | 135 |
| AND16 | 32-36 | 16 | 1,300 | 31.75 | 24.00 | 16.50 | 5/16 | 1/2 | 190 |
| AND25 | 37-40 | 25 | 1,600 | 35.00 | 26.75 | 19.00 | 5/16 | 1/2 | 210 |
| AND43 | 31-45 | 43 | 2,000 | 40.25 | 31.00 | 22.00 | 3/8 | 5/8 | 240 |
| AND70 | 46-55 | 70 | 3,000 | 50.00 | 38.00 | 26.50 | 1/2 | 11/16 | 315 |
| AND100 | 56-60 | 100 | 3,500 | 54.00 | 41.00 | 28.75 | 5/8 | 3/4 | 360 |
Super Hooker Galvanized Anchors
Super Hooker Galvanized Anchor
Penetrates quickly and firmly for maximum holding power
Product Description
Super Hooker Anchor is a great choice for your anchoring needs. This lightweight, hot dipped galvanized Super Hooker anchor has strong wide flukes that penetrate quickly and firmly for maximum holding power. It features a fully welded crown configuration that provides the right angles for ultimate holding power and secure penetration. Hot dip galvanized finish. Stows flat and can be used with most fluke type anchor storage systems.
Seamaster Stainless Steel Anchor
Type 316 stainless steel, precision cut and polished
Product Description
The Seamaster Anchor is precision cut and polished from Type 316 Stainless Steel, then welded & hand polished to a mirror finish. Custom size anchors & engraving available.
Super Hooker Galvanized Anchor
Penetrates quickly and firmly for maximum holding power
Product Description
Super Hooker Anchor is a great choice for your anchoring needs. This lightweight, hot dipped galvanized Super Hooker anchor has strong wide flukes that penetrate quickly and firmly for maximum holding power. It features a fully welded crown configuration that provides the right angles for ultimate holding power and secure penetration. Hot dip galvanized finish. Stows flat and can be used with most fluke type anchor storage systems.
| Super Hooker Galvanized Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Boat Length (ft) | Anchor Weight (lb) | Holding Power (lb) | Anchor Height (in) | Stock Width (in) | Fluke Height (in) | Chain Diam (in) | Rope Diam (in) | Line Length (ft) |
| ANSF3G | to 12 | 3 | 130 | 17.25 | 13.00 | 9.00 | 3/16 | 7/16 | 70 |
| ANSF4G | 12-16 | 4 | 240 | 19.50 | 14.75 | 10.50 | 3/16 | 7/16 | 80 |
| ANSF8G | 17-24 | 9 | 480 | 24.00 | 18.25 | 12.00 | 3/16 | 7/16 | 90 |
| ANSF13G | 25-30 | 14 | 740 | 28.25 | 21.50 | 14.25 | 1/4 | 7/16 | 135 |
| ANSF18G | 31-34 | 18 | 1,050 | 31.75 | 24.00 | 16.50 | 5/16 | 1/2 | 190 |
| ANSF22G | 35-38 | 25 | 1,300 | 35.00 | 26.75 | 19.00 | 5/16 | 1/2 | 210 |
| ANSF40G | 38-43 | 43 | 1,600 | 40.75 | 31.00 | 22.00 | 7/16 | 5/8 | 240 |
| ANSF65G | 44-53 | 75 | 2,400 | 50.00 | 38.00 | 26.50 | 1/2 | 11/16 | 315 |
| ANSF85G | 54-60 | 100 | 3,500 | 54.00 | 41.00 | 28.75 | 5/8 | 3/4 | 360 |
Seamaster Stainless Steel Anchors
Seamaster Stainless Steel Anchor
Type 316 stainless steel, precision cut and polished
Product Description
The Seamaster Anchor is precision cut and polished from Type 316 Stainless Steel, then welded & hand polished to a mirror finish. Custom size anchors & engraving available.
| Seamaster Stainless Steel Anchors | ||||||
|---|---|---|---|---|---|---|
| S7515-0000 | 15 | 22.50 | 17.50 | 13.00 | 0.40 | 0.52 |
| S7520-0000 | 20 | 23.80 | 18.00 | 12.00 | 0.40 | 0.52 |
| S7525-0000 | 25 | 26.80 | 21.50 | 16.00 | 0.50 | 0.56 |
| S7535-0000 | 35 | 28.80 | 23.50 | 17.30 | 0.80 | 0.62 |
| S7545-0000 | 45 | 30.00 | 25.50 | 19.00 | 0.80 | 0.62 |
Galvanized Plow Anchors
Galvanized Plow Anchor
Galvanized finish, ideal for a wide range of seabeds
Product Description
Plow Anchors are favored by blue-water cruisers for their exceptional performance in a wide range of seabeds. They are cast of super-strong steel and have exceptional penetration in weeds, sand, mud and rock. The shank is hinged to prevent breakout on an anchor roller. The eye is used for attaching a trip line and makes breakout easier. Hot Dip Galvanized to prevent corrosion.
Galvanized Plow Anchor
Galvanized finish, ideal for a wide range of seabeds
Product Description
Plow Anchors are favored by blue-water cruisers for their exceptional performance in a wide range of seabeds. They are cast of super-strong steel and have exceptional penetration in weeds, sand, mud and rock. The shank is hinged to prevent breakout on an anchor roller. The eye is used for attaching a trip line and makes breakout easier. Hot Dip Galvanized to prevent corrosion.
| Galvanized Plow Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Boat Length (ft) | Anchor Weight (lb) | WLL (lb) | Chain Diam (in) | Rope Diam (in) | Line Length (ft) | |||
| ANP16 | 26-30 | 16 | 5,000 | 3/16 | 7/16 | 135 | |||
| ANP20 | 31-35 | 20 | 10,000 | 5/16 | 1/2 | 190 | |||
| ANP25 | 36-40 | 25 | 15,000 | 3/8 | 9/16 | 225 | |||
| ANP35 | 41-45 | 35 | 20,000 | 7/16 | 5/8 | 240 | |||
| ANP45 | 46-50 | 45 | 30,000 | 1/2 | 11/16 | 315 | |||
| ANP60 | 51-60 | 60 | 50,000 | 9/16 | 3/4 | 360 | |||
Stainless Steel Plow Anchors
Stainless Steel Plow Anchor
Type 316 stainless steel, precision cut and polished
Product Description
The Plowmaster Anchor is precision cut and polished from Type 316 Stainless Steel, then welded & hand polished. The Plowmaster Anchor is designed for excellent performance in muddy, sandy and hard bottom conditions. Breaking loads 50% to 100% higher than galvanized anchors of competitors. Engraving available.
Stainless Steel Plow Anchor
Type 316 stainless steel, precision cut and polished
Product Description
The Plowmaster Anchor is precision cut and polished from Type 316 Stainless Steel, then welded & hand polished. The Plowmaster Anchor is designed for excellent performance in muddy, sandy and hard bottom conditions. Breaking loads 50% to 100% higher than galvanized anchors of competitors. Engraving available.
| Stainless Steel Plow Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Size (lb) | A (in) | B (in) | C (in) | D (in) | E (in) | K/Hole (in) | ||
| S7025-0000 | 25 | 12.00 | 7.80 | 16.50 | 30.50 | 13 | 0.70 | ||
| S7035-0000 | 35 | 12.80 | 8.50 | 17.50 | 34.50 | 14 | 0.80 | ||
| S7045-0000 | 45 | 14.30 | 10.00 | 20.00 | 39.00 | 17 | 0.80 | ||
| S7060-0000 | 60 | 15.80 | 11.00 | 21.00 | 41.50 | 18 | 0.90 | ||
| S7080-0000 | 80 | 17.50 | 12.00 | 25.00 | 45.00 | 19 | 1.00 | ||
Galvanized Workboat Anchors
Galvanized Workboat Anchor
Designed for larger vessels
Product Description
Workboat Anchors have excellent holding power in sand & mud and are designed for larger vessels. Hot Dip Galvanized.
Galvanized Workboat Anchor
Designed for larger vessels
Product Description
Workboat Anchors have excellent holding power in sand & mud and are designed for larger vessels. Hot Dip Galvanized.
| Galvanized Workboat Anchors | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Anchor Weight (lb) | Holding Power (lb) | Anchor Height (in) | Stock Width (in) | Fluke Height (in) | Anchor Swivel (in) | |||
| ANWB150 | 150 | 8,300 | 49 | 42-1/2 | 29-7/8 | 3/4 | |||
| ANWB200 | 200 | 10,100 | 52-1/2 | 45-1/2 | 33 | 7/8 | |||
| ANWB300 | 300 | 13,000 | 56 | 48-1/2 | 35-1/4 | 1-1/8 | |||
| ANWB400 | 400 | 15,600 | 58 | 50 | 36-9/16 | 1-1/8 | |||
| ANWB500 | 500 | 18,100 | 63 | 54-1/2 | 39-3/4 | 1-1/2 | |||
Anchor Retrieving Kit
Anchor Retrieving Kit
The Anchor Ring Anchor Retrieving System is preferred for open water anchoring on anchor lines rigged with more than 10 feet of chain. The Anchor Ring clips to the line only when you are ready to pull the anchor.
Product Description
Anchor Retrieving Kit
The Anchor Ring Anchor Retrieving System is preferred for open water anchoring on anchor lines rigged with more than 10 feet of chain. The Anchor Ring clips to the line only when you are ready to pull the anchor.
| Anchor Retrieving Kit | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Part # | Ring Size | Polyform A Series Buoy | Flotation Capacity (lbs) | ||||||
| ANFLK3014 | 1/4″ | FPAO | 17 | ||||||
| ANFLK4014 | 1/4″ | FPA1 | 37 | ||||||
| ANFLK5014 | 1/4″ | FPA2 | 74 | ||||||
| ANFLKRS14* | 1/4″ | N/A | N/A | ||||||
| ANFLKS** | N/A | N/A | N/A | ||||||
For customer service and inquiries please call John 303-809-7274 or email john@denverrope.comwww.denverrope.com
